I think every collector of orchids has felt the need of having to replace the support of a raft, and because it has become too small or has deteriorated over time or because they simply do not like the most.
The support of a raft can be conglomerate, in Xaxim, in epiweb, wood or cork, the first three personally will not accept them, if they are proposed to me, I replace them immediately; all my rafts are mounted on cork or of strong wood, resistant to deterioration.
Many collectors have expressed to me their concerns to address this, for it is the fear of losing the orchid or for not knowing how to proceed.
Even if it's for a few months do not like to see legnature that wrap the raft to allow the roots to anchor itself to the support, with my method now you do not see the ligaments and the raft is more pleasing.
For years I mount or replace my rafts, have I missed any subject, but you must proceed delicately.
Let's see how to proceed and what needs:
-The cork or wood (board cherry, oak, locust, lives, etc .. important that contains acid) on which to mount the raft;
-of clear nylon thread, use a 0.35 to 0.40);
-of or sphagnum moss, use them alive, considering ban on the collection, I produce them personally;
-a crocheted (the one used for the proper fit embroidery), an awl, pliers, wire cutters, the galvanized iron wire and elastic thread.
Name:  foto 1.jpg
Views: 750
Size:  347.9 KB
photo 1
I have two orchids to assemble, a Phal. deliciosum Sunrise and a Platystele stenostachia, the first is more simple in that it has large and sturdy roots, one that prendimamo under observation, a Platystele stenostachia, presents with small and thin roots, very delicate, is mounted on a conglomerate.
The put to soak in water for irrigation and leave for about half an hour or more, until the roots is well wet, so they are very elastic and well soaked cork.
We start beginning to chip away, piece by piece the old support, helping with an awl, pliers, etc. taking care to treat the roots very gently, without damaging them, if required we can help with a magnifying glass, this may take too much time, even hours in old plants, we must pay attention to the roots, if you have to put them back to dry bathroom.
Name:  foto 2.jpg
Views: 715
Size:  335.3 KB
photo 2
Now we have released the orchid roots from the old support and let's lay it on the new cork, we put a little bit of moss between the roots, provisionally fix everything with the elastic thread.
Name:  foto 3.jpg
Views: 633
Size:  329.8 KB
photo 3
Now we take the hook and we plant in Cork by taking it out from the opposite side, we tie the nylon thread crochet and pull until it comes out from the back, repeat the operation on the opposite side and fix with a knot.
Name:  foto 4.jpg
Views: 740
Size:  406.4 KB
photo 4

Repeat the process at several points distributed over the whole length orchid up to get a solid anchor, making sure that the plant is firmly anchored to the support.
Name:  foto 5.jpg
Views: 650
Size:  369.3 KB
photo 5
We must ensure that the nodes do not become loose and with time is less anchoring.
Name:  foto 6.jpg
Views: 719
Size:  408.6 KB
photo 6
The elastic thread is no longer needed and we can take it off.
Proceed taking the galvanized iron wire, we plant the cork up and cross it from the plant side we do a little hook that will be planted in the cork as anchor.
Name:  foto 7.jpg
Views: 606
Size:  396.3 KB
photo 7
Our raft is finished.
Name:  foto 8.jpg
Views: 686
Size:  345.1 KB
photo 8
On the opposite side you can enter the classification board, possibly with growing references.
Name:  foto 10.jpg
Views: 684
Size:  328.6 KB
photo 9
In a few months, when the new roots will be anchored to the cork we can remove the nylon threads, cutting and pulling them, I suggest you remove no more than one or two at a time in order to assess the anchor solidity.
As you can see immediately the orchid is pleasant, the anchors are not visible and the holes in the cork will disappear with time.
With the hope of having done something pleasant, oile.